道路標識スロベニア

Roadworks are construction, maintenance, repair or inspection activities carried out on or beside a road.

They may be indicated by a roadworks warning sign, cones, barriers, temporary markings, flashing lights, machinery or workers.

No, not by itself. A separate temporary or permanent speed-limit sign establishes the legal maximum speed.

Yes, when necessary. Narrow lanes, workers, machinery, poor surfaces, congestion or limited visibility may require a substantially lower speed.

Yes. Correctly installed temporary signs must be obeyed for as long as they are in force.

Follow the temporary markings that guide traffic through the works. Local law determines how they take priority over older permanent markings.

Yes. Stop at the line or signal when required and do not proceed until the applicable light permits it.

Obey instructions from workers or controllers who are legally authorised to regulate traffic. Their signals may temporarily replace the ordinary traffic arrangement.

Observe the signs and lane arrows, check mirrors and blind spots and merge safely into the continuing lane.

Zipper merging means that vehicles in an ending or blocked lane merge alternately with vehicles in the continuing lane near the narrowing during congested traffic.

This depends on local law and traffic conditions. Where zipper merging applies during congestion, use both lanes and merge near the narrowing. In flowing traffic, change lanes when a safe gap is available.

Without another traffic control, the driver whose route is obstructed commonly has to yield before moving into the path of approaching or adjacent traffic.

Yes. Temporary signals may allow only one direction at a time through a narrow section.

No. Do not enter a narrow section, intersection or temporary crossing when congestion may leave you stopped inside it.

No. Do not move, pass around or ignore traffic-control equipment unless an authorised person instructs you to do so.

Only when signs and markings permit it and sufficient width and visibility remain. Overtaking is often unsafe in narrow or shifted lanes.

Only where temporary and permanent signs permit it. Do not obstruct workers, machinery, emergency access or temporary pedestrian and cycle routes.

Expect workers to enter the road, machinery to move or reverse and vehicles to leave the worksite. Reduce speed and leave generous space.

Follow the signed temporary cycle route or lane. Check surrounding traffic carefully before leaving a closed or obstructed bike path.

Use the designated temporary walkway or crossing and follow barriers, signs, signals and instructions from authorised personnel.

Traffic may brake suddenly because of queues, lane changes, machinery, debris or changing signals. Additional distance provides more time to react.

Move to the safest available location where possible, activate the hazard warning lights and contact assistance. Avoid standing in a live or narrow traffic lane.

Yes. Rules concerning safe speed, following distance, signalling, priority and vulnerable road users continue to apply unless a lawful temporary arrangement changes them.

It prohibits vehicles whose total height exceeds the displayed value from continuing beyond the sign.

It is commonly a circular regulatory sign showing a height in metres, feet or another local unit between vertical arrows.

The height includes the vehicle, its load and any attached equipment, such as roof boxes, bicycles, machinery, antennas or raised loading equipment.

Yes. Every part of a vehicle combination must fit beneath the restriction, including the towing vehicle, trailer and load.

Not necessarily. Road authorities may display a lower value than the measured clearance to provide a safety margin.

The legal wording commonly prohibits vehicles higher than the displayed value, but drivers should not attempt to pass without a practical safety margin. Measurement errors, movement and road conditions can reduce the available clearance.

Loading, tyre pressure, suspension settings, raised equipment, replacement tyres and road movement can alter the vehicle’s total height.

Yes. The vehicle may rise or lower depending on its suspension mode, speed and load. Use the maximum travelling height when planning the route.

Yes. An arched bridge, tunnel roof or overhead structure may provide different clearance in each lane. Follow lane-specific signs and markings.

Yes. Clearance may be lower near the edge of an arch or where the road slopes sideways. Remain within the authorised marked path.

Yes. A new road surface can raise the road level and reduce the space beneath a bridge or structure.

Yes. Material on the road can raise the vehicle or restrict the usable route. Flooding may also conceal the road surface or another hazard.

They are common at bridges, tunnels, car parks, loading areas, gateways, railway structures and roads with overhead equipment.

It is normally a prohibition. A vehicle that exceeds the displayed height may not pass.

No. The applicable road or posted speed limit remains in force, although drivers should approach cautiously.

No. Traffic lights, priority signs and ordinary priority rules remain applicable.

Yes. An advance sign may show the restriction and the distance to it so that high vehicles can choose another route.

Do not continue. Stop where safe and follow the signed diversion or another suitable route. Do not reverse into traffic without assistance.

No. Navigation may contain outdated or incomplete vehicle restrictions. Traffic signs and the actual road conditions always take precedence.

Yes. Drivers of trucks, buses, motorhomes and vehicles carrying roof loads should know and, where useful, display the vehicle’s maximum travelling height inside the cab.

Stop before the restriction in a safe place and verify the vehicle’s height. Choose another route when safe clearance cannot be confirmed.

Only when signs and markings permit it and the manoeuvre can be completed safely. Do not cross a closed lane, continuous line or opposing traffic merely to gain clearance.

Only in a safe place and when the equipment can be secured correctly afterwards. Never stop beneath the structure or in a live lane to alter the vehicle.

Stop immediately where safe, activate the hazard warning lights and contact the emergency services or police. Do not continue because the vehicle, load or structure may be unstable.

No, when damage may have occurred. Keep away from the structure and follow instructions from the police, road authority or railway operator.

It prohibits vehicles or vehicle combinations whose relevant mass exceeds the value displayed on the sign.

It is commonly a circular regulatory sign showing a mass in tonnes, kilograms or another local unit.

It is normally a prohibition. A vehicle exceeding the displayed limit may not continue beyond the sign.

Actual loaded mass is the weight of the vehicle as it is currently travelling, including the vehicle itself, its load, driver, passengers and other relevant equipment.

Maximum authorised mass is the highest total mass at which the vehicle is legally approved to operate. It is normally recorded in the vehicle documents.

No. A lightly loaded vehicle may have an actual mass below its maximum authorised mass. A restriction may legally refer to either measurement, depending on the sign and local law.

Yes. Cargo, passengers, fuel, equipment and other carried items may all contribute to the vehicle’s actual loaded mass.

Where the restriction concerns actual loaded mass, the driver and other occupants are normally included.

This depends on the wording of the restriction. It may apply to each vehicle separately or to the combined mass of the complete vehicle combination.

An axle-weight limit restricts the amount of mass carried by one axle or axle group rather than the total mass of the vehicle.

A vehicle may comply with the total weight limit while too much of its load is concentrated over one axle, creating excessive stress on the road or bridge.

They are often used at bridges, weak roads, historic centres, tunnels, temporary structures and roads unsuitable for heavy traffic.

Not necessarily. The displayed legal limit may include engineering and safety margins and should not be interpreted as the structure’s exact failure point.

A sign normally prohibits vehicles exceeding the displayed value. The driver must still be certain that the relevant mass does not exceed it.

The most reliable method is to use an authorised or suitable weighbridge. Vehicle documents alone normally show approved limits rather than the vehicle’s current loaded mass.

An estimate may help with planning, but it must include the vehicle, fuel, occupants, equipment, load and trailer. A weighbridge is preferable when the remaining margin is small.

No. Moving cargo within the vehicle does not change its total mass, but it can change the load carried by each axle.

Yes, when done lawfully and safely. The vehicle may continue only after its relevant mass complies and the remaining load is properly secured.

Yes. Temporary restrictions may protect a damaged bridge, weakened road, roadworks structure or road affected by flooding or thawing.

Yes. Lane-specific signs may direct heavier vehicles towards a lane or structure designed to carry them.

Yes. Advance signs may give the distance to the restriction or indicate a diversion so affected vehicles can choose another route.

No. The applicable general, zonal or posted speed limit remains in force.

No. Traffic lights, priority signs and ordinary priority rules remain applicable.

Do not continue. Stop where safe and follow a signed diversion or another route suitable for the vehicle’s mass.

No. Navigation information may be incomplete or outdated. Traffic signs and official restrictions always take precedence.

Only when reversing is lawful and can be completed safely. Use assistance where necessary, particularly with a long or heavy vehicle combination.

The vehicle may damage the road or structure and may be stopped, fined, unloaded or prohibited from continuing under local law.

Traffic lights are signals that use coloured lights, arrows or road-user symbols to regulate traffic movements.

A red light requires road users to stop before the stop line or signal and remain stopped until movement is permitted.

A steady amber light normally requires drivers to stop unless they are already too close to stop safely. It warns that the signal is changing to red.

A green light permits road users to pass the signal, but only when the route is clear and the intended movement is otherwise legal.

No. You may still have to give way to pedestrians, cyclists, oncoming traffic or other road users when turning or following a conditional arrow.

No. Do not enter when congestion is likely to leave you stopped inside the intersection and obstructing crossing traffic.

Stop before the stop line. When no stop line is provided, stop before the traffic light or at another legally prescribed position.

No. The required stop must normally be completed before the stop line. Do not stop on a pedestrian or cycle crossing.

Stop when this can be done safely. Continue only when you are already too close to stop without creating danger.

No. Do not accelerate to avoid stopping. Maintain control and stop unless doing so safely is no longer possible.

They have the same general meaning as circular lights, but the prohibition or permission applies only to the direction shown by the arrow.

It may permit travel in the indicated direction while other movements remain prohibited. Drivers may still have to give way to conflicting traffic and pedestrians.

Not universally. Drivers must follow the complete local sign arrangement. A traffic signal does not necessarily cancel a separate regulatory prohibition.

Only where local law or a specific sign or signal expressly permits it. There is no universal right to turn on red.

It warns of a potential hazard and normally allows cautious passage. The ordinary priority arrangement remains applicable.

Reduce speed, observe the intersection carefully and follow the applicable priority signs or default priority rules.

Its meaning depends on local law. At railway crossings and some movable bridges, flashing red lights normally require road users to stop.

A red cross normally closes the lane, a green downward arrow opens it and an amber diagonal arrow instructs drivers to leave the lane in the indicated direction.

No. Move out of the lane safely before reaching the red cross unless an authorised person or emergency rule directs otherwise.

It warns that the lane is closing or unavailable ahead. Drivers must move into the adjacent lane indicated by the arrow when safe.

Yes. A signal displaying a bicycle symbol applies to the road users legally covered by that signal rather than to general motor traffic.

Yes. Pedestrian lights normally use red and green human figures to indicate whether pedestrians may begin crossing.

It normally warns that the crossing period is about to end. Pedestrians who have not started should wait for the next green signal.

A person who entered lawfully should continue without unnecessary delay. Turning drivers must allow the crossing to be completed safely.

Yes. Public-transport signals may use bars, circles, triangles or other symbols that apply only to authorised service vehicles.

They commonly replace the priority arrangement at that location. Priority signs may apply again when the normal signals are inactive or flashing.

Yes. Instructions from an authorised traffic controller normally take precedence over lights, signs, markings and ordinary rules.

Reduce speed and follow the priority signs, temporary signals, authorised personnel or default priority rules that apply.

Yes, when you entered lawfully and must leave the intersection. Complete the movement cautiously without endangering other road users.

No. Drivers may proceed but must continue at a safe and legal speed.

This depends on local law. In many countries, a driver temporarily stopped in traffic is still considered to be driving and may not use a handheld device.

Pedestrian lights are traffic signals that indicate when pedestrians may begin crossing a road.

They commonly display a red standing person and a green walking person. Their design may vary between countries.

It means that pedestrians must not begin crossing.

It means that pedestrians may begin crossing, provided they still observe the road and cross without unnecessary delay.

No. Turning vehicles, emergency vehicles or traffic following another authorised signal may still cross the pedestrian route. Pedestrians should remain attentive.

It normally warns that the permitted crossing period is about to end. Pedestrians who have not started should consider waiting for the next green signal.

Its meaning varies between countries. It commonly means that pedestrians must not begin crossing, while those already on the road should finish without delay.

A countdown may show approximately how much time remains before the signal changes. It does not remove the duty to cross cautiously.

Begin only when there is enough time to cross safely and without stopping unnecessarily on the road. Waiting for the next green phase may be safer.

Continue crossing at a normal pace towards the nearest safe side. Do not turn back suddenly, stop unnecessarily or run into another traffic stream.

Yes. Drivers should allow pedestrians who entered lawfully to complete the crossing safely, even when vehicle traffic receives permission to proceed.

Some signal systems permit turning vehicles and pedestrians at the same time. Turning drivers must give way where required and must not endanger pedestrians.

It is a signal phase during which conflicting vehicle movements are stopped so pedestrians can cross without permitted traffic turning across their route.

It is a phase in which pedestrians may cross several or all approaches while vehicle traffic is stopped. Diagonal crossing is permitted only when the signals and markings allow it.

They may indicate that the same pedestrian signal applies simultaneously to several crossing directions. The exact meaning depends on local law.

Check that approaching and turning vehicles are stopping and that the route is clear. A green signal does not make a collision impossible.

Yes. They should proceed at a normal pace and should not linger, stop unnecessarily or obstruct traffic on the crossing.

Pedestrians may have to follow the traffic lights controlling vehicles, an authorised officer or the ordinary pedestrian-crossing rules.

A push button normally registers a request for a pedestrian crossing phase. Pressing it does not itself permit crossing; pedestrians must wait for the appropriate signal.

Normally not. Once the request has been registered, additional presses usually have no effect.

Audible signals use sounds to help pedestrians with visual impairments identify when crossing is permitted or when the signal is changing.

Tactile signals may use a vibrating button, rotating cone or raised markings to provide crossing information to pedestrians with visual impairments.

Not normally. A cyclist riding a bicycle must follow the applicable cycle or vehicle signal unless a combined pedestrian-and-cycle signal applies.

A person walking beside a bicycle is normally treated as a pedestrian and follows the pedestrian signal.

They display pedestrian and bicycle symbols and apply to the road users indicated by those symbols.

No. Instructions from an authorised traffic controller normally take precedence over pedestrian lights.

Cross only according to the functioning vehicle signals, priority rules and instructions from authorised personnel. Proceed cautiously and take approaching traffic into account.

A traffic mirror is a convex roadside mirror that helps road users see around an obstruction or into a road with limited visibility.

They may be placed near intersections, narrow roads, bends, car-park exits, private driveways, tunnels or other locations where buildings, vegetation or road geometry obstruct the view.

A convex surface provides a wider field of view than a flat mirror, allowing more of the approaching road to be seen.

No. The reflected image is distorted, and objects normally appear smaller and farther away than they really are.

Not reliably. The curved image makes it difficult to estimate how fast another road user is approaching.

No. Distance can appear greater than it really is, so an approaching vehicle may reach the intersection sooner than expected.

Yes. Its position and viewing angle may leave parts of the road outside the reflected image. Small cyclists, motorcycles or pedestrians may also be difficult to notice.

No. It does not change priority. Drivers must continue to follow stop signs, give-way signs, traffic lights and the ordinary priority rules.

No. Another road user may be outside the reflected area, hidden by glare or too small to notice. Always check the road directly before proceeding.

Yes. The mirror does not replace the mandatory complete stop. Stop at the prescribed position, then use direct observation and the mirror as additional information.

Yes. You may proceed only when traffic with priority can continue without being forced to brake, stop or change direction.

Approach slowly, stop when required and scan the mirror for movement. Then look directly in both directions and continue only after confirming that the road is clear.

No. Alternate between the mirror and direct observation. The mirror should supplement rather than replace normal checks.

Yes. Rain, water droplets and spray may blur or partially obscure the reflected image.

Yes. Dew, condensation, frost, ice or snow may make the mirror difficult or impossible to use.

Yes. Sunlight may create glare or reflections that hide approaching road users.

Yes. Reflected headlights may make it difficult to determine the exact direction, distance or speed of an approaching vehicle.

Yes. Wind, impacts, vandalism, vibration or temperature changes may alter its orientation and make the reflected view inaccurate.

Do not rely on it. Proceed with additional caution and report the defect to the responsible road authority or property owner.

No. The applicable road or posted speed limit remains in force, but restricted visibility normally requires a lower approach speed.

No. Use the horn only where local law permits it and a warning is reasonably necessary to prevent danger.

Yes. It may help them observe approaching traffic, but they must also look directly and follow the applicable crossing and priority rules.

A mirror may generally be installed on private property with the owner’s permission, subject to local rules. Installing one on, above or beside a public road normally requires permission from the road authority.

No. Removing vegetation, relocating parking, improving the intersection layout or changing traffic circulation may provide a safer and more reliable solution.

An international border is the legal boundary between two countries.

It may be identified by a country-name sign, national or regional symbols, flags, border posts, customs facilities or passport-control signs.

No. Borders may be marked differently, and some minor roads or open-border areas may have only a small identification sign or boundary marker.

Not normally. Stop only when required by traffic lights, barriers, officers, customs signs, passport controls or another instruction.

The new country’s traffic laws apply from the international boundary, not merely from the next town or major intersection.

No. The rules change because you have entered another country. The sign identifies that change of jurisdiction.

Yes. Where neighbouring countries use different driving sides, a specially designed road arrangement guides traffic safely from one side to the other.

Yes. The destination country may have different general limits for motorways, built-up areas, rural roads and particular vehicle categories.

No. Drivers must learn the destination country’s general limits and obey any regulatory signs displayed after crossing.

Yes. Colours, symbols, shapes and road-marking conventions may differ, even when neighbouring countries follow similar international standards.

Yes. Requirements concerning safety vests, warning triangles, winter tyres, lights, toll equipment or environmental stickers may differ between countries.

Depending on the journey, drivers may need a passport or identity card, driving licence, vehicle-registration document, insurance evidence, visa or customs documents.

No. Border or immigration control concerns people and travel documents. Customs control principally concerns goods, cargo, money and applicable duties or restrictions.

Yes. Both may operate at the same border facility even though they perform different legal functions.

No. Countries participating in an open-border area may normally cross internal borders without routine checks, although temporary controls may still be introduced.

No. Countries within a customs union may allow goods to move across their internal borders without ordinary customs duties or routine customs formalities.

No. Police, customs and other authorities may still conduct lawful checks, enforce national rules and temporarily control the border where permitted.

Only where local law permits it. External or controlled borders may have to be crossed through an authorised border-crossing point during its operating hours.

Yes. Closures or restrictions may result from security measures, emergencies, severe weather, roadworks or administrative decisions.

Yes. A crossing may restrict heavy vehicles, dangerous goods, agricultural traffic, pedestrians or cyclists because of road design or border-control facilities.

Yes. Commercial goods, restricted products, goods exceeding personal allowances and certain amounts of cash may require declaration.

They may. The destination country may use toll roads, vignettes, distance-based charges, low-emission zones or other payment systems.

No. Navigation information may not include current border controls, vehicle restrictions or document requirements. Follow official signs and instructions.

Check the destination and transit countries’ traffic rules, required documents, insurance, vehicle equipment, tolls and border or customs requirements.

Yes. Follow lawful instructions from authorised border, police and customs officers, even when they temporarily differ from the normal traffic arrangement.

Cycling routes are commonly indicated by direction signs, bicycle symbols, route numbers, colours or destination markers. The design of the signs and route-numbering system varies between countries and regions.

Usually not. A cycling-route sign normally provides direction or route guidance rather than imposing a mandatory direction. However, separate mandatory traffic signs may require cyclists to use a particular cycle path or direction.

No. A cycle path is a specific part of a road or separate path intended for cyclists under local traffic rules. A cycling route is an entire itinerary and may include cycle paths, ordinary roads, cycle streets and other types of infrastructure.

Not necessarily. Many cycling routes use roads and paths that are also open to motor vehicles, pedestrians or other road users. Access is determined by the signs and rules applying to each individual section.

Not automatically. Being on a designated cycling route does not normally change the priority rules. Cyclists must continue to obey traffic lights, give-way and stop signs, crossing rules and other applicable traffic regulations.

No. A route may combine dedicated cycle infrastructure with quiet streets, shared roads, rural roads and other suitable connections. The quality and level of separation from motor traffic can therefore change along the route.

Yes. A cycling route may cross or temporarily follow busy roads. At such locations, cyclists must follow the crossing, priority and traffic-light rules indicated by local signs and markings.

Yes, unless access is restricted by separate traffic signs or regulations. A cycling-route designation by itself does not normally prohibit cars, motorcycles or other vehicles from using an otherwise public road.

Yes. Cycling routes may be designed for daily travel, tourism or recreation. Some form part of regional, national or international networks and may be identified by route names or numbers.

Always follow the official traffic signs, signals and road markings. A route marker provides navigation and does not override a prohibition, mandatory direction, road closure or other traffic regulation.

Parking generally means leaving a vehicle stationary for longer than a brief stop required for passengers, loading or unloading. A vehicle stopped because of traffic lights, congestion, an emergency or another traffic condition is normally not considered parked. The precise legal definitions vary between countries.

Look for parking signs, prohibition signs, road markings and parking-zone signs. Local rules may also permit parking along certain roads even when individual parking spaces are not marked.

No. General traffic rules can prohibit parking even when no specific prohibition sign is present. Common examples include locations where a parked vehicle would obstruct visibility, crossings, intersections, cycle facilities or the movement of other traffic.

Parking on a pavement or sidewalk is prohibited or restricted in many countries unless signs or markings specifically allow it. Vehicles must not force pedestrians into the roadway or block an accessible pedestrian route.

Parking on or close to a pedestrian crossing is generally restricted because a vehicle can hide pedestrians from approaching drivers. The required clearance distance varies between countries.

Many countries prohibit parking within a specified distance of an intersection because parked vehicles can reduce visibility and obstruct turning traffic. Follow the local distance requirements and any signs or markings.

A parking sign identifies a place or area where parking is permitted or regulated. Additional signs or panels may specify time limits, payment requirements, vehicle categories, permits or particular parking arrangements.

Where parking is subject to payment, drivers must follow the instructions displayed locally. Payment may be made through a parking meter, ticket machine, mobile application or another authorised system. The permitted duration and charging periods vary by location.

Spaces marked for people with disabilities are reserved for vehicles displaying or registered with the required disability parking permit. Eligibility, permit display requirements and parking privileges depend on national and local law.

Not necessarily. Local rules may impose a maximum parking duration, even where parking is otherwise permitted. Different limits may apply to abandoned, commercial, heavy or recreational vehicles.

It means that a driver may not voluntarily stop the vehicle in the restricted area. The prohibition normally includes stopping to pick up or drop off passengers or to load or unload goods.

No stopping is the stricter restriction. A no-parking rule may still allow a brief stop for activities such as picking up passengers or loading goods, while a no-stopping rule prohibits these voluntary stops as well.

A driver may have to stop because of an emergency, traffic conditions, a red light, police instructions or another situation outside the driver's control. Such compulsory stops are generally different from voluntarily stopping the vehicle.

A parking disc shows when a vehicle arrived at a time-limited parking space. It allows parking enforcement officers to determine whether the permitted parking period has been exceeded.

It should normally be placed clearly visible behind the windscreen or in another position specified by local traffic rules so that the indicated time can be read from outside the vehicle.

Generally no where the applicable rules prohibit extending the parking period in this way. The vehicle normally has to leave the parking space before a new parking period can begin.

Check behind and around the vehicle for pedestrians, cyclists, other vehicles and obstacles. Use mirrors and cameras where available, but also look directly because monitoring systems can have blind spots.

In many countries, reversing is treated as a manoeuvre and the reversing driver must give way to other road users. The exact legal requirements depend on national traffic rules.

No. Reversing should normally be limited to the distance necessary to complete the manoeuvre safely. Driving forward generally provides better visibility and vehicle control.

An emergency exit is a designated escape route that allows people to leave the traffic area of a tunnel and reach a safer location during an emergency.

Use an emergency exit when evacuation is necessary because of fire, smoke or another serious danger, or when instructed to evacuate by tunnel personnel or emergency services.

No. Tunnel emergency exits are intended for people evacuating on foot. Leave the vehicle when necessary and follow the marked escape route towards safety.

A city limit marks the boundary of a city, town, village, locality or municipality. On roads, it is often indicated by a place-name or boundary sign.

No. A city-limit or locality sign may simply identify a place or administrative boundary. A legally defined built-up area can use a different sign or definition.

No. In some countries a locality or boundary sign has consequences for traffic rules, while in others it mainly identifies the place. Drivers must follow the traffic signs and rules that apply in that country.

Not always. Some signs indicate an administrative municipal boundary, while others identify a city, town, village or locality without exactly following the municipality's legal boundary.

A city limit identifies the boundary of a named place or administrative area. A built-up area is a traffic-law concept that may affect rules such as default speed limits. The two boundaries can coincide, but they do not have to.

A licence plate is a plate displaying the registration identifier assigned to a vehicle. It allows authorities and other authorised systems to identify the vehicle's registration.

Yes. Licence plate, registration plate and number plate are different terms commonly used for the plate displaying a vehicle's official registration number.

Most motor vehicles used on public roads must display one or more registration plates, but requirements differ for motorcycles, trailers, agricultural vehicles and other special vehicle categories.

This depends on the country and vehicle type. Cars commonly require front and rear plates, while motorcycles and certain other vehicles may require only a rear plate.

Yes. A required registration plate must normally remain clearly visible and readable. It should not be hidden by luggage, dirt, accessories or other objects.

Generally no. Changing the characters, colours, dimensions or appearance of an official plate may make it invalid or illegal. Plates and authorised reproductions must comply with local specifications.

Follow the local reporting and replacement procedure. Many countries require the loss or theft to be reported to the police or vehicle-registration authority before a replacement plate can be issued.

A plate must remain legible and compliant with local requirements. If damage prevents it from being read or makes it invalid, it should be replaced according to the local registration procedure.

Some countries allow motorists to request a personalised registration combination. The available characters, formats and prohibited combinations are determined by the registration authority.

This varies between countries. In some systems the plate remains with the vehicle, while in others it remains associated with the registered holder and may be retained or returned when the vehicle is sold.

A charging station is a location where electric vehicles can be connected to an electricity supply to recharge their batteries. A station may contain one or several individual charging points.

Charging stations are intended for vehicles that can be externally charged, such as battery-electric vehicles and plug-in hybrid vehicles. The exact vehicle categories permitted may be indicated by local signs or operator conditions.

Not necessarily. A space beside a charger may be reserved for electric vehicles or vehicles that are charging. Drivers must check the signs and markings before parking there.

Not where the parking space is officially reserved for electric vehicles. An ordinary parking space located near a charger may be different, so the applicable signs and markings determine who may park there.

This depends on the local traffic and parking rules. Many charging spaces require the vehicle to be connected to the charger, even if the vehicle itself is electric.

Charging may be free or subject to payment. The price and payment method are determined by the charging operator, while separate parking charges may also apply.

Yes. Traffic signs, parking regulations or charging conditions may establish a maximum duration to encourage drivers to move their vehicles and make the charger available to others.

Follow the local parking rules and charging conditions. Some locations require vehicles to leave after charging or impose additional fees or time limits when the charging session has ended.

No. A charging station does not allow a driver to ignore no-parking rules, reserved spaces, time limits or other traffic regulations. The vehicle must still be legally parked.

No. Charging stations can provide different charging powers. Some are intended for longer parking periods, while high-power chargers can recharge compatible vehicles much more quickly.

A general danger warning sign indicates that there is a hazard ahead that is not represented by a more specific warning sign in the local traffic-sign system.

It can be used for unusual or uncommon hazards for which no dedicated warning symbol exists. The nature of the danger may be explained by an additional panel, symbol or message.

Look for a supplementary panel, text or symbol accompanying the warning sign. It may describe the hazard or provide information needed to understand the warning.

Increase your attention, observe the road and surroundings carefully and adapt your speed where necessary so that you can respond safely to the hazard.

Not normally. A warning sign alerts road users to danger rather than establishing a numerical speed limit. A separate speed-limit sign may be provided where a specific maximum speed is required.

It is used when the traffic-sign system does not contain a specific symbol that accurately represents the particular hazard.

Yes. A general warning sign may be used for either a temporary or continuing hazard, depending on local signing rules and the circumstances.

Yes. Depending on the country's traffic-sign system, an additional panel may indicate the distance to the hazard, the length of the dangerous section or other useful information.

No. A danger warning sign does not by itself change the priority rules. Drivers must continue to follow traffic lights, priority signs and the normal right-of-way rules.

Not necessarily. The sign normally warns of a hazard ahead of the sign, and the dangerous situation may extend over a section of road. Supplementary information may indicate its location or length.

A dip is a short depression in the road surface where the road falls and then rises again.

A dip can reduce visibility, affect vehicle stability and hide road users or obstacles. Water may also collect in the lowest part of the depression.

Approach at a suitable speed, keep the vehicle under control and be prepared for hazards that may not be visible until you enter or leave the dip.

A pedestrian is primarily a person travelling on foot. Local traffic laws may also treat people pushing bicycles, wheelchairs, prams or certain other devices as pedestrians.

Pedestrians should normally use pavements, sidewalks, footpaths or other areas provided for pedestrians. Where these are unavailable, local rules determine where pedestrians may walk on or beside the road.

This depends on the country's traffic rules. Many countries require or recommend pedestrians to face approaching traffic, but the exact rule varies.

Use a pedestrian crossing, traffic-light-controlled crossing or other designated crossing where required or reasonably available. Where crossing elsewhere is permitted, choose a location with good visibility and cross carefully.

The exact priority rule varies between countries. Drivers are commonly required to give way to pedestrians using or entering designated crossings, but pedestrians must still obey traffic lights and avoid entering the road dangerously.

Yes. Where pedestrian signals are provided, pedestrians must follow their indications and should not enter the roadway while the signal prohibits crossing.

In many traffic systems, a person who dismounts and walks beside a bicycle is treated as a pedestrian. The precise legal classification depends on local law.

This depends on the road layout and local rules. Pedestrians may sometimes use a cycle path when no suitable pedestrian facility is available, but they must not unnecessarily obstruct cyclists or other authorised users.

Yes. Drivers turning into another road must watch carefully for pedestrians crossing the road they are entering and give way where required by local traffic law.

Check carefully for approaching traffic from all relevant directions, make sure there is sufficient time and distance to cross safely, and continue to observe traffic while crossing.

A cyclist is a person who rides and controls a bicycle.

Yes. Cyclists are road users and must follow the traffic rules, signs and signals that apply to them.

This depends on local rules. Cyclists may be required to use a cycle path or designated cycling facility, while in other situations they may ride on the carriageway.

A truck is a motor vehicle designed primarily for transporting goods.

No. Trucks can include lighter goods vehicles as well as heavy trucks. Traffic laws often apply different rules according to the vehicle's maximum authorised mass.

Trucks may have larger blind spots, longer stopping distances and wider turning paths than smaller vehicles, so other road users should avoid remaining unnecessarily close beside or in front of them.

A bus is a motor vehicle designed to transport a relatively large number of passengers. It may be used for public transport, school transport, private services or other passenger transport.

A bus is commonly designed for frequent passenger boarding and may allow standing passengers, while a coach is generally designed for longer journeys with passengers seated. Exact legal definitions vary between countries.

Yes. Driving a vehicle designed to carry more than a specified number of passengers normally requires a dedicated bus or passenger-vehicle driving licence.

Only when the vehicle is designed and approved to carry standing passengers. Coaches and other vehicles designed exclusively for seated passengers must not be used beyond their approved passenger configuration.

Where seat belts are provided and local law requires their use, passengers must wear them correctly. Urban buses designed for standing passengers may have seating positions or operating conditions that differ from coaches.

Yes, where permitted. Bus lanes are commonly reserved for public transport buses, although local signs may also allow taxis, bicycles or other specified vehicles to use them.

No. Some countries require other drivers to give way to buses leaving designated stops, particularly in urban areas, while others apply the normal merging rules.

Yes. Passengers may be boarding, leaving or crossing the road near the bus. Reduce speed where necessary and watch carefully for pedestrians emerging from behind or in front of the vehicle.

They can. Some countries impose lower maximum speeds on buses than on passenger cars, particularly on high-speed roads. Different limits may apply to buses and coaches.

Yes, normally. Buses that satisfy the applicable construction and access requirements may use motorways, but they must obey any vehicle-specific speed limits, lane restrictions and other local rules.

Police help enforce traffic laws, manage traffic, investigate collisions and respond to dangerous situations. They may also carry out roadside checks and direct road users.

Yes. Lawful directions given by an authorised police officer must be followed. In many countries, those directions take precedence over traffic lights, road signs and normal priority rules.

Slow down, follow the officer's directions and stop at a safe location as instructed. Do not make sudden movements or continue driving unless directed to do so.

Yes, where authorised by local law. A police officer controlling traffic may instruct road users to proceed even when a traffic light or sign would normally require them to stop.

Yes. Police may require drivers to provide documents such as a driving licence, vehicle registration, identification or proof of insurance according to local law.

Yes. Traffic police may conduct legally authorised alcohol and drug checks using procedures such as breath, saliva or other approved tests.

Yes. Roads or lanes may be temporarily closed or traffic diverted because of collisions, emergencies, investigations, public events or other safety concerns.

Reduce speed, remain alert and follow all directions. Do not enter a closed area or interfere with emergency personnel, and leave sufficient space for emergency vehicles.

Follow the local rules for priority vehicles. Drivers generally have to make sufficient space, give way and stop where necessary so that the emergency vehicle can pass safely.

Yes, where local law permits it. Police or another authorised authority may require a vehicle to be moved when it obstructs traffic, creates danger or must be removed for operational reasons.

An ambulance is a specially equipped vehicle used to provide emergency medical assistance and transport sick or injured people.

This depends on the local traffic rules and warning signals being used. Ambulances responding to emergencies commonly use flashing lights and a siren to indicate that other road users must make way.

Remain calm and make sufficient space for it to pass. Slow down or stop where necessary, but avoid sudden or dangerous manoeuvres.

Not necessarily in your exact position. Move or stop in a way that creates a safe passage without blocking an intersection, pedestrian crossing or another part of the road needed by the ambulance.

Emergency vehicles may be allowed to pass a red light during an urgent response under special legal conditions. The precise rules differ between countries, and the ambulance driver must still take appropriate precautions.

Many countries permit emergency vehicles to depart from certain normal speed rules during an urgent mission, subject to safety requirements and national legislation.

Yes, when responding to an emergency and legally permitted to do so. Other road users should create space and keep emergency corridors or access routes clear where required.

You should not use the passage created for an ambulance as a way to bypass congestion. Maintain a safe distance and continue to obey the normal traffic rules.

No. The use of warning lights and sirens depends on the urgency of the mission and local regulations. An ambulance transporting a patient does not necessarily need to use emergency signals throughout the journey.

Reduce speed and remain alert. Medical personnel, patients or other emergency workers may be entering the road, and the ambulance may need to move unexpectedly.

A taxi is a vehicle used to transport passengers for payment, normally providing journeys requested by individual customers.

Depending on the local system, taxis may be available at taxi stands, airports, railway stations, on the street or through telephone and app-based booking services.

Yes. Taxi services are generally subject to licensing and operating requirements, although the exact rules concerning vehicles, drivers, fares and permitted operating areas vary between jurisdictions.