交通ルールオランダ

A motorway is normally identified by a special motorway sign at its entrance. It commonly has separate carriageways, controlled entrances and exits, and no ordinary intersections or direct access to neighbouring properties.

Motorways are primarily intended for motor vehicles capable of travelling safely at motorway speeds. Pedestrians, cyclists, animals and certain slow vehicles are generally prohibited, but the exact access requirements differ between countries.

There is no universal motorway speed limit. The applicable limit depends on the country, road section, vehicle category and driving conditions. Posted or variable speed-limit signs may replace the general national limit.

Use the entrance or acceleration lane to observe motorway traffic and adjust your speed where possible. Enter only when there is a safe gap and follow the local priority and merging rules.

Move into the correct lane in good time and signal when required. Enter the exit or deceleration lane before reducing your speed, unless traffic, signs or road conditions require you to slow down earlier.

Follow the local keep-left or keep-right rule and any lane-direction signs. Lanes closer to the centre of the motorway are commonly used for overtaking, but lane-use rules differ between countries and vehicle categories.

Voluntary stopping and parking are normally permitted only in designated parking or service areas. Drivers may still have to stop because of congestion, an emergency or another unavoidable situation.

Reversing, making a U-turn and driving against the direction of traffic are generally prohibited. If you miss an exit, continue to the next suitable exit.

Move the vehicle out of the traffic lanes when this can be done safely, activate the hazard warning lights and follow the local breakdown procedures. Leave the vehicle safely, keep away from moving traffic and use a warning triangle or safety vest where required by local law.

A motorway normally has the highest level of access control and is governed by specific motorway rules. An expressway may have similar characteristics but may permit different road users or contain lower-standard junctions. The legal distinction varies between countries.

An expressway may be identified by a special road sign or by its road classification. It often has multiple lanes, limited access and junctions designed for faster traffic, but its exact appearance differs between countries.

No. A motorway normally has full access control and stricter design and traffic rules. An expressway may have partial access control, ordinary intersections, traffic lights or direct entrances. The legal distinction varies between countries.

Not necessarily. Many expressways have separate carriageways for opposing traffic, but some countries also classify undivided roads as expressways. Drivers should rely on local signs and road rules rather than the road’s appearance alone.

Expressways are generally intended for motorised traffic. Pedestrians, cyclists, animals, mopeds and slow vehicles may be restricted or prohibited, but the permitted road users depend on local law and traffic signs.

There is no universal expressway speed limit. The applicable limit depends on the country, road design, location, vehicle category and posted signs. An expressway sign does not always impose a particular speed by itself.

Yes. Unlike a motorway, an expressway may have level intersections, roundabouts, pedestrian crossings or traffic lights. Drivers must therefore remain prepared for crossing traffic and changes in priority.

Use an entrance or acceleration lane where one is provided, observe approaching traffic and enter only when there is a safe gap. Where the road has an ordinary intersection, follow the applicable priority signs and local rules.

Follow the local keep-left or keep-right rule, lane arrows and traffic signs. Lanes nearer the centre are commonly used for overtaking, but special lane restrictions may apply to heavy vehicles or particular destinations.

These actions are often restricted on expressways because of the speed and flow of traffic. Stop or park only where permitted, and never reverse or make a U-turn unless the road design and local rules clearly allow it.

Move the vehicle away from moving traffic when this can be done safely, activate the hazard warning lights and follow the local breakdown procedures. Use a warning triangle or safety vest where required and wait in a protected location away from traffic.

A residential area commonly contains homes, driveways, parked vehicles and local streets. It may also have special entrance signs, traffic-calming measures or shared road space, but its appearance and legal status differ between countries.

Not necessarily. A built-up area may include residential, commercial and industrial streets. A residential area is primarily associated with housing and local access and may form only one part of a larger built-up area.

No. In many countries, special residential-zone rules apply only where an official entrance sign is displayed. An ordinary neighbourhood may remain subject to the normal rules for the surrounding road or built-up area.

There is no universal residential-area speed limit. Some countries apply a very low limit in signposted residential or shared-space zones, while ordinary residential streets may follow the general built-up-area limit or a posted zone limit.

The rights of pedestrians depend on the country and the type of residential area. In some signposted shared-space zones, pedestrians may use the whole road and drivers must give them special consideration. On ordinary residential streets, the normal pedestrian and crossing rules may apply.

Playing may be expressly permitted in certain legally designated residential or shared-space zones. This is not automatically allowed on every residential street. Drivers should nevertheless remain especially alert for children, who may enter the road unexpectedly.

Residential areas are normally accessible to local motor traffic, cyclists and pedestrians, but additional signs may restrict certain vehicles or through traffic. A residential area is therefore not necessarily a pedestrian-only zone.

Drive at a speed that allows you to stop safely, watch both sides of the road and expect pedestrians, cyclists, children, pets and vehicles emerging from entrances. Leave enough space and avoid unnecessary acceleration, noise or aggressive overtaking.

Overtaking is not universally prohibited, but it may be restricted by local law, signs or road design. Even where it is permitted, drivers should not overtake when the limited space or presence of vulnerable road users makes it unsafe.

Follow the local parking signs, markings and general parking rules. Do not block entrances, pavements, crossings, sight lines or the passage of other road users. Special residential zones may permit parking only in designated spaces.

Motor vehicles are normally still permitted in a residential area, although they may be subject to strict speed and parking rules. In a pedestrian zone, vehicle access is generally prohibited or limited to specific users, purposes or times.

A traffic zone is a defined area in which a particular restriction, prohibition or obligation applies throughout the included roads rather than only at one location.

A traffic zone normally begins with a zone-entry sign showing the applicable rule. A corresponding end-of-zone sign indicates where that rule stops applying.

An ordinary sign usually applies to a particular road, direction, lane or section. A zone sign applies throughout a designated area, which may contain several roads and intersections.

Usually, yes. A zonal rule commonly continues through intersections until an end-of-zone sign is reached. The exact effect of intersections depends on local law.

A traffic zone normally ends when you pass the corresponding end-of-zone sign. The normal road rules or another signed regulation then apply.

Yes. A zone may contain several regulations, such as a speed limit together with parking or access restrictions. Drivers must observe every applicable sign.

Yes. A local sign may introduce a different or more restrictive rule on a particular road or section. Whether the original zonal rule resumes afterwards depends on local law and the type of regulation.

Common examples include speed zones, parking zones, low-emission zones, pedestrian zones, cycling zones, school zones and zones restricting particular vehicle categories.

No. A built-up area is a broader legally defined urban area. A traffic zone imposes a specific signed rule and may be located inside or outside a built-up area.

No. A residential area describes an area mainly used for housing. It may contain one or more traffic zones, but the terms do not automatically have the same legal meaning.

Not necessarily. The sign, symbol or additional panel may limit the rule to particular vehicles, road users, times or circumstances.

Observe the entrance sign carefully, identify every displayed rule and remember that the regulation may continue across several roads and intersections until the zone ends.

A speed limit is the maximum legal speed permitted on a road, lane or within a designated area. It does not require drivers to travel at that speed.

A speed limit is commonly displayed as a number on a regulatory traffic sign. General limits may also apply automatically because of the country, road category, vehicle type or surrounding area, even when no speed-limit sign is present.

No. It is the highest speed legally permitted under suitable conditions. Drivers must reduce their speed whenever travelling at the limit would be unsafe.

Yes. Drivers should travel more slowly when required by traffic, weather, visibility, road conditions or nearby vulnerable road users. Driving unnecessarily slowly may nevertheless be prohibited when it obstructs normal traffic.

Not always. Lower limits may apply to heavy vehicles, buses, vehicles towing trailers, novice drivers or other vehicle categories. The lowest applicable limit must be respected.

A default speed limit applies automatically to a particular road type or area when no traffic sign indicates another limit. Examples include general limits for motorways, built-up areas or roads outside built-up areas.

Usually, yes. A legally placed speed-limit sign normally introduces another maximum speed, although lower vehicle-specific or special-road limits may continue to apply.

A speed restriction normally begins at the location of the sign. Drivers should reduce their speed before passing the sign so that they are already travelling within the limit when it takes effect.

A signed limit may end at an intersection, an end-of-limit sign, another speed-limit sign or the beginning or end of a legally defined area. The exact rule differs between countries.

This depends on local law. An ordinary speed restriction may end at an intersection in some countries, while a zonal speed limit normally continues across intersections until an end-of-zone sign.

A speed zone is an area in which the displayed maximum speed applies throughout all included roads. The limit normally remains in force until the corresponding end-of-zone sign.

A variable speed limit is displayed on an electronic or changeable sign and may be adjusted according to congestion, weather, incidents or roadworks. When activated, it has the same legal importance as another applicable regulatory speed sign.

Yes. Signs positioned above individual lanes may impose different limits on those lanes. Drivers must observe the limit applying to the lane they use.

Yes. Temporary limits may be introduced near roadworks, collisions, hazards or special events. Drivers must follow the temporary traffic signs and instructions that are legally in force.

No. Overtaking does not normally permit a driver to exceed the applicable maximum speed. The manoeuvre must be completed safely while respecting the speed limit.

Some countries impose specific lower limits in rain, snow or other conditions. Even where the numerical limit does not change, drivers must reduce their speed sufficiently for the conditions.

A footpath is a path or part of a road intended primarily for pedestrians.

Not necessarily. A pavement or sidewalk normally runs alongside a roadway, while a footpath may follow an independent route or pass through an area without an adjacent roadway.

Pedestrians are the primary users. Depending on the signs and local regulations, cyclists or other categories may also be permitted on shared paths.

Normally no when the path is specifically reserved for pedestrians. Cyclists may have to dismount unless local rules or signs allow cycling.

In many countries, a person walking a bicycle by hand is treated as a pedestrian and may therefore use pedestrian facilities, subject to local rules.

Normally no when the route is reserved for pedestrians. Limited access may sometimes be authorised for maintenance, emergency or other specific purposes.

Yes. A route may be designated as a shared pedestrian-and-cycle path. Users must follow any signs indicating how the space should be shared.

This depends on the local traffic rules and type of shared facility. Cyclists and other permitted users should always avoid endangering pedestrians.

Yes. Where a path crosses a roadway, pedestrians must follow the applicable crossing, priority and traffic-light rules.

Yes. Pedestrian paths can form part of the wider public-road network even though ordinary motor traffic may not use them.

Yes. Many countries use a specific pedestrian symbol to indicate a path reserved or compulsory for pedestrians.

Use the appropriate cycle facility or roadway. Where local law permits it, a cyclist may also dismount and continue as a pedestrian.

A bike path may be identified by a bicycle traffic sign, bicycle symbols, coloured surfacing or road markings. It may run beside the carriageway or follow a completely separate route.

Not always. A bike lane is normally marked directly on or beside the carriageway, while a bike path may be physically separated from motor traffic. The terminology and legal distinction vary between countries.

This depends on local law and the signs displayed. Some bike paths are mandatory, while others are optional. Cyclists may also be permitted to leave a path to turn, overtake or avoid an obstruction.

Yes. Some bike paths are two-way, but others may be used only in the direction indicated by signs, markings or their position beside the road. Cyclists should not assume that every path permits travel in both directions.

Pedestrians may use a bike path where it is designated as a shared-use path or where local law permits it. On a cycle-only path, pedestrians may be prohibited or permitted only when no suitable pedestrian facility is available.

This depends on the country, vehicle category, road speed and traffic signs. Some bike paths permit or require certain mopeds or speed pedelecs, while others are reserved exclusively for ordinary bicycles.

Normally not. Motor vehicles may cross a bike path to enter another road or property where this is permitted, but they must follow the applicable priority rules and must not endanger path users.

Priority depends on the road layout, signs, signals and local law. Drivers crossing a continuous bike path commonly have to give way to its users, but cyclists approaching a separate cycle crossing may not automatically have priority before entering it.

No. A marked cycle crossing does not universally give an approaching cyclist priority. Cyclists should enter cautiously and observe approaching traffic unless signs, signals or local rules clearly give them priority.

Some countries or local authorities impose specific limits, particularly on shared paths. Even without a posted limit, cyclists must travel at a safe and considerate speed for the width, visibility and number of other users.

Normally not. Stopping or parking on a bike path can force cyclists into motor traffic and may be expressly prohibited by law.

Reduce speed, give a clear warning where appropriate and leave sufficient space. Pedestrians may change direction unexpectedly, especially on a shared path.

Slow down and check surrounding traffic before leaving the path. Avoid the obstruction safely and return to the bike path when permitted and practical.

This depends on local law and the available width. Even where riding side by side is permitted, cyclists must not block, endanger or unnecessarily hinder other path users.

A bike path is intended primarily or exclusively for cycling. A shared-use path is legally intended for cyclists together with pedestrians or other indicated road users, who must use the space considerately.

A cycling street is a road where cycling is given a prominent position while motor vehicles may usually continue to use the road under additional restrictions.

It may be identified by special entrance signs, bicycle symbols, coloured surfacing or distinctive road markings. The legally required signs differ between countries.

No. A bike path is a separate part of the road or a separate route intended for cyclists. On a cycling street, cyclists and motor vehicles normally share the carriageway.

Not always. A cycling street may refer to one individual street, while a cycling zone may include several connected streets governed by the same rules. Local terminology varies.

Usually, yes. A cycling street is not normally closed to motor traffic, although access may be restricted by additional signs or local regulations.

This depends on local law. In some cycling streets, cyclists may use a larger part of the carriageway or ride in the centre of the lane. In others, the normal positioning rules continue to apply.

This depends on the rules of the country and the available road width. Cyclists may often ride side by side where this does not endanger or unlawfully obstruct other road users.

Some countries expressly prohibit motor vehicles from overtaking cyclists on cycling streets. Elsewhere, overtaking may remain permitted only when the legally required distance and other safety conditions can be respected.

Normally, cyclists may overtake other vehicles when the manoeuvre is permitted and can be completed safely. They must still observe local overtaking, lane and intersection rules.

There is no universal speed limit. Many countries impose a low maximum speed, commonly 30 km/h or less, but drivers must follow the signs and laws applying locally.

No. A cycling street does not normally give cyclists automatic priority at every intersection. Traffic lights, priority signs, crossings and the ordinary priority rules remain applicable.

Not necessarily. Pedestrians normally use pavements, crossings and other designated facilities. A cycling street is different from a pedestrian zone or residential shared-space area.

Stopping and parking depend on the ordinary rules and any local signs or markings. Vehicles must not block cyclists, pavements, crossings, entrances or other traffic.

No. Coloured surfacing may make the street easier to recognise, but it does not necessarily have legal meaning by itself. The official signs and local regulations determine which rules apply.

The special rules normally end at an end sign, the end of the designated street or another legally defined boundary. The exact rule differs between countries.

A pedestrian zone is an area where pedestrians are the principal road users and ordinary motor-vehicle access is prohibited or strictly restricted.

A pedestrian zone is normally identified by a special entrance sign. An end sign indicates where the pedestrian-zone rules stop applying.

No. A pavement is a part of a road intended for pedestrians. A pedestrian zone may include the entire width of one or more streets, squares or other public spaces.

Not always. Emergency vehicles, maintenance vehicles, public transport, delivery vehicles, residents or other authorised traffic may be permitted under local rules.

This depends on the traffic signs and local law. Cycling may be permitted at all times, during specified hours or not at all. Cyclists who are not permitted to ride may normally walk while pushing their bicycles.

Where cycling is permitted, cyclists must normally adapt their speed and avoid hindering or endangering pedestrians. They may be required to dismount when the zone is crowded.

This depends on how electric scooters are legally classified and on the signs displayed. They may be treated as pedestrians at very low speeds, as cyclists or as another vehicle category.

Usually, yes. Pedestrians may generally use the full width of the pedestrian zone, although marked sections may be reserved for authorised vehicles, cyclists or public transport.

Authorised drivers must normally travel cautiously, leave pedestrians sufficient space and stop when necessary. The precise priority rule depends on local law.

There is no universal numerical limit. Many countries require authorised vehicles to travel at walking pace or another very low speed.

Playing may be permitted because the area is primarily reserved for pedestrians, but this depends on local law. Children must still be supervised where authorised vehicles, cyclists or public transport are present.

Deliveries may be permitted during specified hours or under particular access conditions. Drivers must observe the information displayed at the entrance.

Taxis may be permitted to enter for passenger collection or drop-off, but access may be restricted to certain destinations, times or permit holders.

Parking is normally prohibited or limited to specially authorised places. Brief stopping for authorised loading, unloading or passenger access may be permitted under local rules.

Not necessarily. A pedestrian zone may include several connected streets and intersections. Its rules normally continue until the corresponding end sign is passed.

A pedestrian zone is primarily reserved for pedestrians and usually restricts motor traffic. A residential shared-space area normally permits general local traffic but imposes very low speeds and special pedestrian and parking rules.

The special rules normally end at an end-of-pedestrian-zone sign. The ordinary rules of the surrounding road or another signed zone then apply.

A road slope is a section of road that rises or descends over a particular distance. It may also be called a gradient, incline or decline.

A steep slope may be indicated by a warning sign showing an ascending or descending road. The sign may also display the gradient as a percentage.

A gradient of 10% means that the road rises or falls approximately 10 metres for every 100 metres travelled horizontally. It does not mean that the road is inclined at 10 degrees.

An ascent rises in the direction of travel, while a descent falls in the direction of travel. The same section of road is therefore an ascent in one direction and a descent in the other.

Not normally. It warns of a hazard rather than setting a numerical limit. Drivers must still respect the applicable speed limit and reduce their speed further when necessary.

Reduce speed before the descent, select a suitable gear and maintain a safe following distance. Avoid allowing the vehicle to gain excessive speed.

Use a gear that provides sufficient engine braking and helps keep the vehicle at a controlled speed. The appropriate gear depends on the vehicle, gradient and road conditions.

No. Coasting reduces engine braking and may make it harder to control the vehicle’s speed. Keep the transmission engaged while descending.

Continuous braking on a long descent can cause the brakes to become excessively hot and lose effectiveness. Select a suitable gear, control speed early and use the brakes progressively when needed.

Brake fade is a reduction in braking performance caused by excessive heat. It can occur when the brakes are used continuously during a long or steep descent.

Select a suitable gear before the engine begins to struggle and maintain a steady speed where possible. Be prepared for heavy or low-powered vehicles travelling slowly ahead.

Yes. Heavy vehicles, vehicles towing trailers and low-powered vehicles may slow considerably. Other drivers should maintain a safe distance and avoid impatient manoeuvres.

Do not overtake when the crest prevents you from seeing far enough ahead. Overtaking near a hilltop may also be expressly prohibited by local law, signs or road markings.

The road surface itself may hide approaching traffic, stopped vehicles, pedestrians or other hazards beyond the crest.

Some countries give priority to uphill traffic, while others rely on signs or ordinary obstruction rules. Drivers must follow local law and cooperate when passing is difficult.

Reduce speed and use a passing place where available. The driver who can reverse or move aside more safely should cooperate, subject to any applicable priority signs or local rules.

They reduce traction and make acceleration, braking and steering more difficult. Increase the following distance, use smooth controls and reduce speed before entering the slope.

Cyclists may travel slowly and move less steadily when climbing, while they may reach high speeds when descending. Drivers should leave sufficient space and avoid overtaking without a clear view.

Use the parking brake, select the appropriate gear or parking position and follow local rules concerning wheel position. Make sure the vehicle cannot roll into traffic.

Yes. A trailer increases the load on the engine and brakes and may affect stability. Drivers should use a suitable gear, maintain additional distance and avoid excessive speed.

A bus stop is a designated location where buses stop so that passengers can board or leave the vehicle.

Watch for buses entering or leaving the stop, passengers near the roadway and pedestrians who may cross the road.

Parking or stopping at or near a bus stop is often restricted or prohibited so that buses can reach the stop safely. The exact restrictions depend on local traffic rules.

A dead-end road is a road that provides no through route for some or all vehicles. Traffic entering it normally has to return by the same route.

A dead end may be indicated by a blue rectangular sign showing a road blocked at one end. The exact colour, design and symbol vary between countries.

Normally not. It generally provides information rather than prohibiting access. Drivers may enter to reach a destination unless another sign restricts entry.

No. A dead-end sign warns that the road does not continue as a through route. A no-entry sign prohibits drivers from entering in the indicated direction.

No. It may end at a wall, gate, turning area or private property, or it may continue as a narrower path that motor vehicles cannot use.

Sometimes. A separate symbol, sign or visible path may indicate that pedestrians can continue beyond the point where motor traffic ends.

Sometimes. A sign may indicate a through route for cyclists, but cyclists must still follow any access, direction and path-use rules that apply.

No. The normal road, zonal or posted speed limit remains applicable. Drivers should nevertheless reduce speed when space, visibility or nearby pedestrians require it.

No. Traffic lights, priority signs and the ordinary intersection rules continue to apply.

Not solely because the road is a dead end. Priority depends on the signs, road surface, road category and local priority rules.

A driver may turn around where the manoeuvre is legal, safe and does not obstruct other road users. Local signs or road markings may prohibit it.

Reverse only when necessary and when the route is clear. Give way to all other road users and avoid reversing for a long distance where a safer turning place is available.

A driver performing a turning or reversing manoeuvre must normally give way to other road users.

The dead-end sign itself does not normally prohibit parking. Drivers must follow the ordinary parking rules and must not block entrances, pedestrian routes, emergency access or turning areas.

Only where parking is permitted and sufficient room remains for other vehicles to turn. Blocking the turning area can force vehicles to reverse for an unsafe distance.

Trucks, buses and vehicles towing trailers may not have enough space to turn around. Drivers should check the route and any length, width, weight or access restrictions before entering.

Yes. Emergency and service vehicles may need access to properties within it. Other vehicles should not block the road or its turning space.

Continue cautiously to a suitable turning place. Turn around or reverse only after checking carefully for pedestrians, cyclists, vehicles and other obstacles.

No. Temporary closures, private access, gates, roadworks or outdated navigation information may still prevent passage. Drivers must observe the actual road and signs.

A stop sign requires a driver to come to a complete stop and give way before proceeding.

A stop sign is commonly a red octagonal sign displaying the word STOP. Some countries use another legally recognised design, so drivers must learn the signs used locally.

Yes. The obligation to stop applies even when the road appears completely clear.

A complete stop means that the vehicle has ceased moving entirely. Merely slowing down or allowing the vehicle to continue rolling does not satisfy the requirement.

Stop before the stop line where one is provided. Without a line, stop at the legally prescribed position before entering the intersection, crossing or priority road.

No. The required first stop must be made before the line. If visibility is limited, move forward cautiously after stopping and stop again where necessary before proceeding.

Yes. Each driver must make an individual complete stop. Following another vehicle through without stopping is not permitted.

No. After stopping, you must continue to give way to all road users who have priority.

Give way to traffic on the road being entered or crossed and to pedestrians, cyclists or other road users who have priority under the applicable rules.

A stop sign always requires a complete stop. A give-way sign requires the driver to yield but normally allows continued movement when the road is clearly free.

Yes. After stopping and giving way, you may turn in any direction permitted by signs, signals, lane arrows and road markings.

This depends entirely on local law and traffic signs. A stop sign does not by itself permit a turn against a red light.

No. It imposes a stopping and yielding obligation. The normal posted or general speed limit remains applicable before and after the intersection.

In many countries, cyclists are drivers and must stop unless a specific sign or local rule provides an exception.

The order in which drivers may proceed depends on local rules, commonly involving arrival order, vehicle position and turning direction. Drivers should communicate cautiously and never assume another driver will yield.

Apply the local priority rule and proceed only when the intentions of the other driver are clear. Avoid forcing the other vehicle to brake or change direction.

Where functioning traffic lights control the same movement, they commonly take precedence over the stop sign. Local rules determine what applies when the lights are switched off or flashing.

Yes. Instructions from an authorised traffic officer normally take precedence over traffic signs and ordinary priority rules.

Yes. A correctly placed temporary stop sign at roadworks, an event or another temporary traffic arrangement must be obeyed.

If you recognise that a stop sign applies, reduce speed and obey it. Report damaged, obscured or missing signs to the responsible road authority where appropriate.

A give-way sign requires drivers to allow traffic with priority to proceed first. The driver must slow down and stop when necessary.

It is commonly an inverted triangular sign with a red border and a light-coloured centre. In some countries, it is called a yield sign.

No. You must stop only when necessary to give way or obtain a sufficiently clear view. You may continue slowly when the road is clearly free.

Giving way means allowing another road user to continue without being forced to brake, accelerate, stop or change direction because of your movement.

Stop before the give-way line where one is provided. Without a line, stop before entering the intersection or priority road at a position where you can observe traffic safely.

You may move beyond the line only when this does not interfere with traffic that has priority. Where visibility is limited, first slow or stop at the line and then move forward cautiously.

A stop sign always requires a complete stop. A give-way sign permits the driver to continue without stopping when the road is clearly free and it is safe to proceed.

Only when slowing down is sufficient to let all priority traffic proceed safely. If another road user would be hindered, the driver must slow further or stop.

Give way to traffic travelling on the road being entered or crossed and to any pedestrians, cyclists or other road users who have priority under the applicable rules.

No. Check every direction from which lawful traffic may approach, including cycle paths, one-way roads with authorised contraflow traffic and separate carriageways.

The sign determines priority at the particular location. The priority arrangement at later intersections may be different unless the road is separately identified as a priority road.

No. You may proceed only when it is safe. Another driver’s hesitation or courtesy does not remove your responsibility to avoid danger.

Yes. Each driver must observe the road and make an individual decision. You may not follow another vehicle through without checking that the way remains clear.

Normally, yes. Cyclists are generally treated as drivers and must obey the sign unless a supplementary sign or local rule provides otherwise.

Yes. Some countries use supplementary signs or path-specific signs to require cyclists to give way while other traffic follows a different priority arrangement.

No. It regulates priority rather than speed. Drivers must still approach slowly enough to observe traffic and stop when necessary.

No. Drivers must still obey traffic lights, lane arrows, mandatory-direction signs and turning prohibitions.

Many roundabout entrances have give-way signs requiring entering traffic to yield to vehicles already circulating. Drivers must follow the actual signs because roundabout priority rules differ between countries.

Functioning traffic lights commonly take precedence over priority signs controlling the same movement. The give-way sign may apply again when the lights are switched off or flashing, depending on local law.

Yes. Instructions from an authorised traffic officer normally take precedence over traffic signs and ordinary priority rules.

Reduce speed substantially and stop when necessary. Move forward cautiously only after giving way and checking that the road can be entered without danger.

A roundabout is a circular road arrangement where traffic travels in one direction around a central island before leaving through the chosen exit.

A roundabout is normally identified by a circular-direction sign, a central island and entry roads controlled by signs, markings or local priority rules.

The direction depends on the country’s driving side. Traffic normally travels anticlockwise in right-hand-traffic countries and clockwise in left-hand-traffic countries.

Priority differs between countries and roundabout designs. Entering traffic commonly gives way to traffic already circulating, but drivers must always follow the actual priority signs and signals.

Not always. Stop when required by a stop sign, traffic light or approaching priority traffic. Otherwise, reduce speed and enter only when there is a safe gap.

No. The sign arrangement depends on local law. Some circular intersections use ordinary priority rules or traffic lights instead.

Reduce speed, observe the signs and markings, choose the appropriate lane and check for pedestrians, cyclists and circulating traffic.

Follow the lane arrows and destination signs. As a general guide, use the lane appropriate for your exit, but exact lane-selection rules differ between countries and roundabout layouts.

Yes, where the road layout and local rules permit it. Before leaving, change lanes safely and give way to road users already travelling in the lane you wish to enter.

This depends on local law. Some countries require a signal for particular exits, while others require no signal when entering.

Usually, yes. Signal in the direction of the exit early enough to inform other road users, but not so early that your intention becomes misleading.

No. A direction indicator communicates your intention but does not permit you to force another road user to brake or change direction.

Only when the lane markings permit it and the manoeuvre can be completed safely. Check mirrors and blind spots, signal where required and give way to traffic already in the target lane.

Continue around the roundabout and approach the exit again. Do not stop, reverse or cut suddenly across another lane.

Normally not. Some small roundabouts have a mountable central section intended only for vehicles that cannot otherwise negotiate the road safely.

Priority depends on whether cyclists use the carriageway, a continuing bike path or a separate cycle crossing. Drivers and cyclists must follow the signs, markings and local priority rules.

Check mirrors and blind spots for cyclists, mopeds, motorcycles and vehicles beside you. Also check for pedestrians crossing the exit road.

Pedestrian priority depends on crossings and local law. Drivers should approach exits slowly and be prepared to yield to pedestrians crossing or about to cross.

Not universally. The posted or general road limit applies, but drivers must travel slowly enough to negotiate the roundabout safely.

Passing another vehicle may be permitted on a multilane roundabout, but drivers must remain within their lane and avoid unsafe lane changes. Local overtaking restrictions may apply.

Follow local signs and parking rules. Stopping or parking on the circulating roadway is commonly prohibited or unsafe because it obstructs traffic and reduces visibility.

No. A circular junction may be governed by traffic lights, ordinary priority rules or another road design. Its legal status depends on its signs and local definition.

A priority road is a road on which drivers normally have priority over traffic entering from intersecting side roads.

It is normally indicated by a priority-road sign at or near its beginning. A corresponding end sign indicates where its continuing priority status stops.

Normally, yes, while the priority-road designation remains in force. Drivers must still observe traffic lights, authorised officers and any signs applying at a particular intersection.

Not necessarily. A priority road commonly continues across successive intersections until an end sign or another legally defined change in priority.

Side roads are commonly controlled by give-way or stop signs, but sign placement and legal requirements differ between countries.

Where the priority-road signs apply, drivers entering from intersecting side roads must normally give way regardless of whether they approach from the left or right.

No. A priority-road sign normally creates continuing priority across several intersections. Another sign may grant priority only at the next intersection.

No. The priority route may turn at an intersection. A supplementary diagram may show which branch retains priority.

Priority does not remove the duty to signal. Use the direction indicators whenever following or leaving the priority route involves a change of direction or lateral movement.

No. Approach every intersection at a safe speed and remain prepared for another road user to fail to give way.

No. The applicable general, zonal or posted speed limit remains in force.

Functioning traffic lights normally control the intersection instead of the priority signs. Local rules determine what applies when the lights are switched off or flashing.

Yes. Instructions from an authorised traffic officer normally take precedence over traffic signs and ordinary priority rules.

Yes, where the applicable crossing rules give them priority. Priority over side-road traffic does not remove duties towards pedestrians.

You must still give way to oncoming traffic, pedestrians, cyclists and other road users where the normal turning rules require it.

Cyclists using the road or a continuing bike path may have priority over entering or turning traffic, depending on signs, markings and local law.

Not automatically. Roundabout priority is determined by its own signs, signals and local rules.

Priority-road status does not itself permit or prohibit overtaking. Drivers must follow the ordinary overtaking rules, markings and visibility requirements.

This depends on local law and signs. Some countries prohibit parking on priority roads outside built-up areas, while other parking rules may apply inside towns and cities.

No. A driver entering the road from a property, parking place or other off-road location normally performs a manoeuvre and must give way to road users already present.

No. Do not enter when congestion would force you to stop inside the intersection and obstruct crossing traffic.

Its continuing priority normally ends at an end-of-priority-road sign. Drivers must then follow the signs or ordinary priority rule applying at the next intersection.

A railway crossing is a place where a road or path crosses railway tracks at the same level.

It may also be called a level crossing or, particularly in North America, a railroad crossing.

It may be indicated by warning signs, crossbuck signs, barriers, flashing lights, bells or road markings. The design differs between countries.

A protected crossing uses full or partial barriers to block road traffic when a train approaches. A crossing without barriers relies on signs, lights, bells or the road user’s own observation.

Not necessarily. You must stop when required by lights, barriers, signs, an approaching train or an authorised person. At an unprotected crossing, slow down and proceed only after checking that no train is approaching.

Flashing red lights mean stop and do not enter the crossing. Remain stopped until the signal permits you to continue.

No. Do not enter while a barrier is lowering, rising or closed. Wait until the crossing is fully open and all prohibiting signals have stopped.

No. Never drive, cycle or walk around or underneath a closed or moving barrier.

A warning bell or audible signal normally means that the crossing is closing or that a train is approaching. Do not enter the crossing while it is sounding.

In some countries, a flashing white light indicates that the crossing equipment is operating and road users may pass when the route is clear. Its exact meaning depends on local law.

Reduce speed, look and listen carefully in both directions and cross only after making sure that no train or other rail vehicle is approaching.

Not automatically. Another train may approach on a second track. Wait until all warning signals stop and the crossing is fully open.

Do not enter the crossing unless there is enough room beyond the tracks for your entire vehicle. Never rely on traffic moving before a train arrives.

No. Railway tracks must always remain clear. Do not stop because of congestion, traffic lights or another obstruction beyond the crossing.

Overtaking is often prohibited or restricted because another vehicle can obstruct the view of an approaching train or warning signal. Follow local signs and overtaking rules.

No. Stopping or parking on the tracks creates an immediate and potentially fatal danger.

Yes. Pedestrians and cyclists must obey barriers, lights, bells and authorised personnel in the same way as other road users.

Where possible, cross the rails at an angle close to 90 degrees. Rails can trap a bicycle wheel, especially when they are wet or cross the road diagonally.

Make sure the entire vehicle and any trailer can clear the crossing without stopping. Consider the available space, road gradient, turning room and traffic beyond the tracks.

Observe all height restrictions and warning signs. Electrified railway lines may have overhead equipment that can be struck by an excessively high vehicle or load.

Treat the crossing with extreme caution. Do not assume that no train is approaching merely because the lights or barriers are not operating.

Evacuate everyone immediately, move well away from the railway and contact the emergency services or railway operator. Do not remain in the vehicle or return for belongings.

Not always. A railway crossing normally crosses tracks that are separate from the carriageway, while tram or street-running railway tracks may form part of the road itself.

A school area is a road or group of roads near a school where drivers should expect large numbers of children, pedestrians, cyclists and stopping vehicles.

It may be identified by school warning signs, speed-zone signs, flashing lights, road markings, coloured surfacing or traffic-calming measures. The signs differ between countries.

No. Special school-area rules normally apply only where signs, signals or local legislation establish them.

There is no universal school-area speed limit. The applicable limit depends on the country, region, signs and whether a variable restriction is active.

Some limits apply permanently, while others apply only during displayed times or when flashing or variable signs are active. Drivers must observe the actual sign arrangement.

Yes, when necessary. The displayed speed is a maximum. Children, congestion, poor visibility or vehicles stopping near the school may require a much lower speed.

Children may have difficulty judging speed and distance, may be hidden by parked vehicles and may enter the road unexpectedly.

Reduce speed early, increase your observation and be prepared for children crossing, cyclists changing direction, vehicle doors opening and cars stopping suddenly.

No. Priority depends on crossings, traffic lights, authorised crossing supervisors and local rules. Drivers must nevertheless take exceptional care to avoid endangering children.

Yes. Drivers and other road users must follow lawful instructions given by an authorised person controlling traffic for children.

This depends on local pedestrian rules. Drivers should remain prepared for children to cross unexpectedly, even where they are required to use a nearby crossing.

Not by itself. A school warning sign alerts drivers to children but does not normally create the legal effect of a pedestrian crossing.

No. Traffic lights, priority signs and the ordinary intersection rules remain applicable unless another traffic arrangement provides otherwise.

Overtaking may be restricted by signs or local law. Even where it is permitted, drivers should not overtake when children, crossings, limited visibility or stopped vehicles make the manoeuvre unsafe.

Only where stopping is permitted and can be completed safely. Do not stop on a crossing, pavement, bike path, bus stop or another prohibited or dangerous location.

Follow the parking signs and markings. Do not block entrances, pavements, bike paths, crossings, visibility or access for buses and emergency vehicles.

It blocks traffic and visibility and may force children to walk between moving vehicles or enter the road from behind an obstruction.

Expect children to enter or leave the vehicle and possibly cross the road. Reduce speed and follow any special warning lights, signs or local school-bus rules.

Normally, yes. They must follow the applicable road, bike-path, speed and priority rules. Drivers should expect inexperienced young cyclists.

No. A school area normally remains open to traffic under special caution or speed rules. A school street temporarily restricts or excludes motor traffic during specified periods.

Not universally. A school area may form part of a Zone 30, use another speed limit or have a variable restriction that applies only at particular times.

They normally end at an end sign, at the end of the stated time period or when the variable signal is no longer active. The surrounding road rules then apply.

In right-hand traffic countries, overtaking normally takes place on the left. In left-hand traffic countries, it normally takes place on the right. National rules can provide exceptions in particular situations.

Make sure there is sufficient visibility and space, check mirrors and blind spots, ensure that nobody behind has already started overtaking and confirm that you can safely return to your normal position after passing.

Do not overtake where signs or road markings prohibit it or where visibility, approaching traffic, intersections, crossings, bends, hills or other conditions make the manoeuvre unsafe.

It warns that animals may enter or cross the road in the area ahead.

Depending on the symbol and local conditions, it may refer to deer, cattle, horses, sheep, goats, wild boar or other animals.

It is commonly a triangular warning sign displaying the silhouette of an animal. The species shown may indicate the type of animal most likely to be encountered.

No. It indicates an increased likelihood of animals crossing, not that animals will be present every time.

No. The normal posted or general speed limit remains applicable, but drivers must reduce speed when necessary to react safely.

No automatic priority is created by the warning sign. Drivers must nevertheless avoid danger and allow animals already on the road to pass safely.

Reduce speed, increase your following distance and scan the road, verges, fields and vegetation for movement or reflected eyes.

Animal activity is often greater around dawn, dusk and darkness, although animals may cross at any time.

Many animals travel in groups. When one animal crosses, others may follow immediately from the same direction.

Avoid unnecessary horn use or engine revving because it may frighten an animal and make its movement less predictable. Use a warning only when reasonably necessary to prevent danger.

Use the appropriate lights without dazzling other road users. When an animal is visible, reduce speed and avoid relying on full beam to make it move away.

Slow down smoothly, stop when necessary and allow it enough time and space to leave. Avoid sudden acceleration or aggressive steering.

Avoid an uncontrolled swerve that could cause a collision with another vehicle, tree, barrier, cyclist or pedestrian. Brake firmly while maintaining control and steer only when a safe escape path is clearly available.

Pass only when the animals and their handlers have sufficient space. Drive slowly, avoid noise and be prepared for an animal to change direction unexpectedly.

Reduce speed, leave a large lateral distance and pass quietly. Avoid sounding the horn, accelerating sharply or passing when oncoming traffic prevents sufficient clearance.

Follow lawful instructions from an authorised person and cooperate with handlers controlling animals on or across the road.

The warning sign does not necessarily prohibit overtaking, but overtaking should be avoided when animals, limited visibility or approaching traffic make the manoeuvre unsafe.

Maintain enough following distance to see beyond the vehicle ahead. Be prepared for it to brake suddenly when an animal enters the road.

Reduce speed, keep both hands firmly in control and avoid sudden movements. Animals may react unexpectedly to quiet or fast-approaching two-wheeled vehicles.

Stop safely, activate the hazard warning lights and check for injured people. Contact the emergency services or police when necessary and do not approach a wounded wild animal, which may defend itself.

Normally not. Keep a safe distance and allow the police, wildlife authorities or an animal-rescue service to handle it.

Yes. Drivers remain responsible for observing the road and adjusting their speed even where no animal warning sign is displayed.

Roadworks are construction, maintenance, repair or inspection activities carried out on or beside a road.

They may be indicated by a roadworks warning sign, cones, barriers, temporary markings, flashing lights, machinery or workers.

No, not by itself. A separate temporary or permanent speed-limit sign establishes the legal maximum speed.

Yes, when necessary. Narrow lanes, workers, machinery, poor surfaces, congestion or limited visibility may require a substantially lower speed.

Yes. Correctly installed temporary signs must be obeyed for as long as they are in force.

Follow the temporary markings that guide traffic through the works. Local law determines how they take priority over older permanent markings.

Yes. Stop at the line or signal when required and do not proceed until the applicable light permits it.

Obey instructions from workers or controllers who are legally authorised to regulate traffic. Their signals may temporarily replace the ordinary traffic arrangement.

Observe the signs and lane arrows, check mirrors and blind spots and merge safely into the continuing lane.

Zipper merging means that vehicles in an ending or blocked lane merge alternately with vehicles in the continuing lane near the narrowing during congested traffic.

This depends on local law and traffic conditions. Where zipper merging applies during congestion, use both lanes and merge near the narrowing. In flowing traffic, change lanes when a safe gap is available.

Without another traffic control, the driver whose route is obstructed commonly has to yield before moving into the path of approaching or adjacent traffic.

Yes. Temporary signals may allow only one direction at a time through a narrow section.

No. Do not enter a narrow section, intersection or temporary crossing when congestion may leave you stopped inside it.

No. Do not move, pass around or ignore traffic-control equipment unless an authorised person instructs you to do so.

Only when signs and markings permit it and sufficient width and visibility remain. Overtaking is often unsafe in narrow or shifted lanes.

Only where temporary and permanent signs permit it. Do not obstruct workers, machinery, emergency access or temporary pedestrian and cycle routes.

Expect workers to enter the road, machinery to move or reverse and vehicles to leave the worksite. Reduce speed and leave generous space.

Follow the signed temporary cycle route or lane. Check surrounding traffic carefully before leaving a closed or obstructed bike path.

Use the designated temporary walkway or crossing and follow barriers, signs, signals and instructions from authorised personnel.

Traffic may brake suddenly because of queues, lane changes, machinery, debris or changing signals. Additional distance provides more time to react.

Move to the safest available location where possible, activate the hazard warning lights and contact assistance. Avoid standing in a live or narrow traffic lane.

Yes. Rules concerning safe speed, following distance, signalling, priority and vulnerable road users continue to apply unless a lawful temporary arrangement changes them.

It prohibits vehicles or vehicle combinations whose relevant mass exceeds the value displayed on the sign.

It is commonly a circular regulatory sign showing a mass in tonnes, kilograms or another local unit.

It is normally a prohibition. A vehicle exceeding the displayed limit may not continue beyond the sign.

Actual loaded mass is the weight of the vehicle as it is currently travelling, including the vehicle itself, its load, driver, passengers and other relevant equipment.

Maximum authorised mass is the highest total mass at which the vehicle is legally approved to operate. It is normally recorded in the vehicle documents.

No. A lightly loaded vehicle may have an actual mass below its maximum authorised mass. A restriction may legally refer to either measurement, depending on the sign and local law.

Yes. Cargo, passengers, fuel, equipment and other carried items may all contribute to the vehicle’s actual loaded mass.

Where the restriction concerns actual loaded mass, the driver and other occupants are normally included.

This depends on the wording of the restriction. It may apply to each vehicle separately or to the combined mass of the complete vehicle combination.

An axle-weight limit restricts the amount of mass carried by one axle or axle group rather than the total mass of the vehicle.

A vehicle may comply with the total weight limit while too much of its load is concentrated over one axle, creating excessive stress on the road or bridge.

They are often used at bridges, weak roads, historic centres, tunnels, temporary structures and roads unsuitable for heavy traffic.

Not necessarily. The displayed legal limit may include engineering and safety margins and should not be interpreted as the structure’s exact failure point.

A sign normally prohibits vehicles exceeding the displayed value. The driver must still be certain that the relevant mass does not exceed it.

The most reliable method is to use an authorised or suitable weighbridge. Vehicle documents alone normally show approved limits rather than the vehicle’s current loaded mass.

An estimate may help with planning, but it must include the vehicle, fuel, occupants, equipment, load and trailer. A weighbridge is preferable when the remaining margin is small.

No. Moving cargo within the vehicle does not change its total mass, but it can change the load carried by each axle.

Yes, when done lawfully and safely. The vehicle may continue only after its relevant mass complies and the remaining load is properly secured.

Yes. Temporary restrictions may protect a damaged bridge, weakened road, roadworks structure or road affected by flooding or thawing.

Yes. Lane-specific signs may direct heavier vehicles towards a lane or structure designed to carry them.

Yes. Advance signs may give the distance to the restriction or indicate a diversion so affected vehicles can choose another route.

No. The applicable general, zonal or posted speed limit remains in force.

No. Traffic lights, priority signs and ordinary priority rules remain applicable.

Do not continue. Stop where safe and follow a signed diversion or another route suitable for the vehicle’s mass.

No. Navigation information may be incomplete or outdated. Traffic signs and official restrictions always take precedence.

Only when reversing is lawful and can be completed safely. Use assistance where necessary, particularly with a long or heavy vehicle combination.

The vehicle may damage the road or structure and may be stopped, fined, unloaded or prohibited from continuing under local law.

It warns that vehicle speeds may be measured or enforced on the road ahead or throughout a specified section.

No. A speed-limit sign establishes the maximum legal speed. A radar sign only warns that compliance with an applicable limit may be monitored.

Check the most recent speed-limit sign, variable sign, speed-zone sign or general limit applying to the road and vehicle category.

No. It does not normally change the existing limit. Drivers must nevertheless travel more slowly when traffic, visibility, weather or road conditions require it.

It may announce a permanent camera, a mobile-control area or a section where enforcement can occur. The exact meaning depends on the country and sign design.

No. Drivers should never rely on assumptions about whether equipment is operating and should respect the speed limit at all times.

A fixed speed camera is permanently installed at a particular location and measures the speed of passing vehicles.

A mobile speed camera is temporarily positioned in a police vehicle, trailer, roadside unit or another approved location.

Lidar uses laser pulses to measure the speed and position of vehicles. It may be used by police officers or in temporary automatic installations.

Average-speed enforcement records a vehicle at two or more points and calculates its average speed across the controlled section.

No. Average-speed enforcement considers the travel time across the complete measured section rather than speed at only one point.

Yes. Some systems monitor vehicle speed and whether a vehicle passes a red traffic signal.

No. Some authorities announce speed cameras, while others permit enforcement without advance warning. The rules differ between countries and regions.

Yes. The absence of a warning sign does not normally prevent police or authorised authorities from carrying out a lawful speed check.

The applicable limit remains a maximum rather than a target. Drivers must reduce speed whenever travelling at that limit would be unsafe.

No. Check your speed and reduce it smoothly when necessary. Sudden braking can cause a rear-end collision.

Only while remaining within the applicable limit and driving safely. The restriction may continue, and another camera or average-speed section may follow.

No. Passing a camera or radar sign does not end the applicable speed restriction.

A radar speed display measures an approaching vehicle and shows its current speed, sometimes with a colour, message or smiley symbol.

Not necessarily. Many displays are preventive devices intended to make drivers aware of their speed and may collect anonymous traffic statistics without issuing penalties.

No. The roadside display is generally informational. Drivers remain responsible for observing the vehicle’s speedometer and the legal speed limit.

Yes. The technical ability to measure a motorcycle and the method used to identify it depend on the enforcement equipment.

Yes. Modern systems may measure vehicles in one or more lanes and may distinguish between traffic directions or vehicle categories.

Yes. Heavy vehicles, buses, trailers or other vehicle categories may be subject to lower limits than passenger cars on the same road.

Release the accelerator and reduce speed smoothly and safely. Do not brake harshly or make an abrupt lane change.

A selective barrier is a physical access-control device that blocks some traffic while allowing specified road users or authorised vehicles to pass.

Common examples include fixed bollards, removable posts, folding posts, retractable bollards, gates, rising barriers and width-filtering installations.

They may prevent through traffic, protect pedestrian or cycling routes, control access to restricted areas or allow only residents, public transport, deliveries or emergency services to enter.

Not normally. The permitted users are determined by traffic signs, permits, access systems and local regulations.

Only when cycling is permitted and sufficient safe space is provided. Cyclists must follow the signs applying to the road or path.

Pedestrians may pass where pedestrian access is permitted and a safe route is available. They should not walk beneath a moving gate or through a vehicle-only opening.

Only when motorcycles are legally permitted beyond the barrier and the opening is intended for them. Being physically able to fit through does not create permission.

Emergency vehicles may have keys, remote controls, automatic recognition or another authorised method of opening the barrier. Other road users must keep the access clear.

They may enter only when local access rules, permits or traffic signs authorise them. Permission may apply only during specified hours.

A retractable bollard is a post that can rise from or lower into the road surface to control vehicle access.

It may operate through a badge, remote control, access code, number-plate recognition, timer, control centre or automatic detection system.

Only after confirming that you are authorised and the bollard is fully lowered. Do not move merely because another vehicle has activated it.

No, unless your own access is also authorised and the system clearly permits it. The barrier may rise immediately after the first vehicle.

Red lights normally require road users to stop, while another signal may indicate when passage is permitted. Follow the displayed signals and local instructions.

Stop at a safe distance and wait until it has completed its movement. Never drive, cycle or walk beneath a moving gate or across a rising bollard.

Do not force, move or drive around it. Use the intercom or contact the operator, road authority or emergency service indicated at the location.

No, unless you are specifically authorised. Removing or repositioning access-control equipment may create danger and allow prohibited traffic to enter.

No. Traffic signs and access restrictions remain applicable even when the physical barrier is temporarily open or lowered.

No. An open physical barrier does not cancel a regulatory traffic sign.

Not by itself. Drivers must follow the applicable speed limit and approach slowly enough to stop before the installation.

No. Traffic lights, priority signs and ordinary priority rules remain applicable unless another traffic arrangement indicates otherwise.

Do not stop or park where the vehicle would block authorised access, emergency services, pedestrians or cyclists.

They may be difficult to see, especially in darkness, congestion or poor weather. A collision can cause a rider to fall into nearby traffic or other obstacles.

Reduce speed, identify the intended opening and pass through in a straight and controlled line. Avoid overtaking another cyclist at the barrier.

Approach slowly, wait for the access system to respond and check for pedestrians and cyclists before crossing their route.

Stop safely, activate the hazard warning lights where appropriate and report the collision. Do not continue if the vehicle, barrier or access system may be damaged.